Участий в СП:483
Сообщения: 11831 Откуда: ост. ЖД больница
Баллы репутации: 113
о! Я дочке перед школой сделала ежедневник похожий из джинсы, спереди только распечатала ее любимые винкс- на машинке прострочила, написала контуром по ткани ее имя, а сзади как раз с кармашком джинса. Тоже всякую всячину складывает.
It might take you a couple trial & error to get the fish looks right. The first time I did this fish for Gallery Idol, I didn't have any direction on how to do it. I basically figured it out myself just by looking at the end result. Took me at least an hour for my first try. This time, it only took 10 minutes.
Step 1: Using a 5/8" ribbon, cut it to about 7"-8". I prefer longer, so you can play with it easier. Overlap them just like in the picture below. The opening in between t he 2 ribbon is basically the fish mouth. You can adjust it to however big or wide you want the mouth to be and glue the overlap ribbon. I used "Love My Tapes" permanent adhesive for this. And make sur eyou only glue the very top part to the 2nd, and not to the 3rd or bottom layer or you'll end up with sickly looking fish with flat head. You want the head to puff a bit. Puffy head = healthy fish.
Step 2: To tie the body together, I folded my 5/8" ribbon in half & glued it (see the skinny strip above). If you have a skinnier ribbon, then you can use the skinny ribbon for it. Now, you want to pinch the ribbon together, like the picture below.
Step 3: Using a glue dot, wrap the skinny ribbon around the body. Make sure you put the glue dot on the back side to keep the fish look neat. Cut the end of both end, so it looks like fish tail.
Cut two 2" long skinny ribbon for the fin. Or if you don't have one, cut the 5/8" ribbon in half like I did. If you do this, then you have to seal the fray end with the tip of hit glue gun or used a lighter. Just remember, fire hot! If you use lighter, make sure you don't get the fire too close. Only close enough to get it sealed the edges. Sorry, couldn't take pic for when I did this since hubby wasn't anywhere close when I did this, so no second person to take the pic & I can't hold lighter & camera at the same time.
Step 4: Overlap & glue the 2" ribbon like shown below.
Step 5: Glued the fin to the body. As you can see, on the above picture I attached the fin right in the middle of the body. That was wrong position. The picture below show the right position. Add a wiggly eye and you're done!!
So, what you think? Easy, right? With a fish like this, you don't need much of anything else to make your card shine. I made a super simple, CAS looking card. I do adore my fish.
_________________ «В конце концов, все будет хорошо. Если ещё не всё хорошо, значит, это не конец» (c)пёрто
Существуют специальные токопроводящие перчатки для работы с сенсорными экранами планшетных компьютеров, смартфонов и телефонов в холодное время года. Но ассортимент их небольшой и они больше напоминают строительные перчатки. Такие не будешь носить повседневно. Но можно любые перчатки приспособить для работы с емкостным сенсорным экраном, прошив их в районе подушечки указательного пальца токопроводящими нитками.
Но и такие нитки тоже не просто достать. Не спешите прошивать перчатки проволокой, в витых проводах старых телефонов (соединяющих трубку с самим телефоном) есть металлизированные нити, которые хорошо подойдут для этого дела. При прошивке перчаток, не спешите обрывать нить, сначала попробуйте, есть ли контакт. Если нет, сделайте еще несколько стежков, добиваясь стопроцентного отклика сенсорного экрана.
И вот я думаю, а метанитью вышивальной можно такое сделать? И не будет ли экран царапаться?
Размещаю в 2х темках, в надежде, что откликнется кто-то из мастеров. Есть обычное кресло (стульчик). Дочка хочет вооот такой. если нужно, закуплю ткани какие скажете ))) Девочки, помогите осуществить дочкину мечту-подарок на НГ )))